NEW Old Stock
Ex our workshop stores, we used a lot of these in our prototype handmade PCB's but of course they are equally suitable for general hobbyist work.
Each drill size has it's own ORIGINAL tube and is marked on the top cap indicating the size
I have spent a LOT of time removing the drill bits from each tube, counting them, checking the bit condition and looking for any signs of damage or even useage. Not an easy task as some of these drill bits are extremely small!
These are offered in quantity breaks (mix up's are fine too), doesn't matter which size, with a heavy discounting automatically applied for those who would just like to take the lot off my hands!
HISTORY:
Over the years we undertook massive amounts of prototyping and of course, made our PCB's and then went through the laborious task of drilling them all! To do this job properly, we kept a very wide range of drill bits ... here are some of the very small drill bits that are eager to do work for someone else.
These very specialised, high quality drill bits (you will NEVER find these sizes at Bunnings!) are very expensive but as I have no further use for them, out they go at crazy prices!
Make a nice strong coffee, sit down and then take a look at distributors such as RS Electronics for current pricing and they do not have the wide range I am offering either. I remember these cost us a small fortune at the time and they are even more expensive now (and hard to come by in these sizes)
If you are new to prototyping or hobbyist drilling, NEVER use those "el-cheapo" Asian sets of drill bits - we tried them out yonks ago and after just a few holes through fibre glass substrates, they end up being just pins with the cutting teeth all blunted - a complete waste of money, never again!
All quantities are PER DRILL BIT
P+N, SUTTON & SILVER JET - Drill Bits
P + N is Patience & Nicholson (Boral)
These are often referred to as "drill jobbers" meaning that the shaft is much longer than the diameter of the drill bit
Steel
High Speed
SIZE, QUANTITY & MANUFACTURER
All sizes are in millimetres
0.35 (1) P + N
0.38 (5) P + N
0.40 (7) P + N
0.42 (6) P + N
0.45 (6) P + N
0.48 (4) P + N
0.50 (5) P + N
0.52 (5) P + N
0.55 (4) P + N
0.60 (8) P + N
0.65 (2) P + N
0.70 (9) 7 P + N & 2 SUTTON
0.75 (6) P + N
0.80 (2) P + N
0.85 (10) SILVER JET
0.90 (2) P + N
0.95 (6) P + N
1.00 (18) 4 P + N & 14 SUTTON
1.05 (7) P + N
1.10 (9) P + N
1.15 (4) P + N
1.20 (12) P + N
1.25 (6) P + N
1.30 (9) P + N
1.35 (4) P + N
1.40 (7) P + N
1.45 (5) P + N
1.50 (11) P + N
1.55 (10) P + N
A total of 190 drill bits - I am "all over" looking at drill bits!
COSMETIC CONDITION:
(Applies to every drill bit)
NO RUST OR OXIDISATION
NO broken shafts or cutter
NO bent bits
*** The photograph shows all of the above drill bits in their little pill boxes, ORIGINAL tubes supplied by the manufacturer with a push on lid.
Since examining all of these and resealed the tubes, I have now placed them into an outer plastic tube and completely sealed it. These will be supplied in the same manner, whether just a few drill bits are purchased or the total quantity as one lot.
Obviously, if you are purchasing a lesser number than the whole lot PLEASE let me know which size and quantity you are after.
